![]() E) When SURROUND MODE is the same in between INPUT source change before and after, EVENT of SURROUND MODE and CHANNEL VOLUMEĭoes NOT return. Volume of all channels, It described in B) ) returns as EVENT. D) Since SURROUND MODE changes simultaneously when the INPUT source changes, the SURROUND MODE (and also the value of the channel The data of an intact channel is set to "50". C) CHANNEL VOLUME returns the data of ALL channels by the present SURROUND MODE also including an intact channel. B) Since CHANNEL VOLUME changes simultaneously when the SURROUND MODE changes, the value of the channel volume of all channels Others A) COMMAND is receivable also during transmission of EVENT. SIDVD : Select Input source DVD MSSTEREO : surround Mode Set to STEREO MVUP : Master Volume UP PWON : system PoWer ON PWSTANDBY : system PoWer STANDBY SI? : Request command for now playing input source > Return RESPONSE SI*** The example of a command * is the meaning of 0x0D. DVD : function name SUPER STADIUM : surround mode name *Special Parameter- ? : for request command SI : Select Input source MS : surround Mode Setting MV : Master Volume setting PW : system PoWer setting PARAMETER : ASCII CODE ( up to 25 characters) ex. Command structure: COMMAND + PARAMETER + CR (0x0D) COMMAND: ASCII CODE of 2 characters Ex. *ASCII CODE which can be used is from 0x20 to 0x7F: the alphabet and the number of 0-9, and space (0x20), some signs, AND carriage return (0x0D) - It is used only as a pause sign. *The form of RESPONSE presupposes that it is the same as that of EVENT.īasic specification: The command by ASCII CODE, parameter expression The RESPONSE should be sent within 200ms of receiving the COMMAND. RESPONSE : The message sent to a controller (Touch Panel etc.) from a system (AVR) if the request command (COMMAND+?+CR(0x0D)) has came from a controller. **Refer to the following table for the contents of COMMAND and EVENT. *The form of EVENT presupposes that it is the same as that of COMMAND. EVENT : The message sent to a controller (Touch Panel etc.) from a system (AVR) The result is sent, when a system is operated directly and a state changes. COMMAND : The message sent to a system(AVR) from a controller(Touch Panel etc.) A command to a system is given from a controller. Protocol specification The following three data forms are defined. This setting is reducing the power consumption in the standby mode. OFF- Use this setting when not using the AVR-2112CI/AVR-1912 connected in a network. ON-Use this setting when using the AVR-2112CI/AVR-1912 Connected in a network. (1)Press MENU button, then Menu appears on FL-display (and GUI) (2)Select Manual Setup > Network Setup > Other > Network Standby (3)Set parameters described below. Do not set this parameter when Gateway is not on the local network. Set the address of Gateway when Gateway is on the local network. When sets "ON, you can confirm the Subnet Mask that is set by server. When sets "ON, you can confirm the IP address that is set by server. "OFF"-Use this setting when DHCP server is not on the local network. "ON"-Use this setting when DHCP server is on the local network. ![]() (1)Press MENU button, then Menu appears on FL-display(and GUI) (2)Select Manual Setup > Network Setup > Network Connecting > Detail. NETWORK SETUP of AVR-2112CI/AVR-1912 >Procedure of Network Setup mode. Ethernet Connector type RJ-45(10BASE-T/100BASE-TX)Ĭommunication system : A half duplex Communication speed : 10Mbps/100Mbps Communication port : TCP port 23 (telnet) Communication data length : 135bytes (maximum) RS-232CĬonnector type: DB-9pin female type, slave straight connection (DCE type) ( 1pin : GND, 2pin : TxD, 3pin : RxD, 5pin : Common(GND), 4,6,7,8,9pin : NC )Ĭommunication format: Synchronous system : Tone step synchronization Communication system : A half duplex Communication speed : 9600bps Character length : 8 bits Parity control : None Start bit : 1 bit Stop bit : 1 bit Communication procedure : Non procedural Communication data length : 135 bytes (maximum) Application model : AVR-2112CI/AVR-1912 Application terminal: RS-232CĮthernet Connector specification.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |